Fueling

Injector Dynamics 1065 cc/min high impedance fuel injector set of eight for GM LS2 engine. Direct connection to OE injector harness.Injector Dynamics Part Number 1050.48.14.15.8No returns on injectors that have been in contact with fuel.

Injector Dynamics 1065cc/min high impedance fuel injector set of six for GT-R R35. Optionally available set of 91.3 US-Denso harness adapters; otherwise, will come with unassembled USCAR electrical connector that installer must affix to injector harness that will require special tools.Injector Dynamics Part Number...

Aerospace grade trigger switch for secondary pumps Gold plated internal contacts and Kapton diaphragm ensure reliable long term service Preset for 10inHg actuation (normally closed, OFF/OPEN with more than 10 inHg vacuum) 1/8 NPT male interface is compatible with our push on boost/vacuum hose...

Complete kit to mount aftermarket fuel rails to your Hemi engine when the original fuel line is being used. Crossover line is unassembled. The hose must be cut to length and the hose ends must be installed to the hose. INCLUDES: Fore Innovations Hemi...

Unassembled APP® connector, same as what we use on FC2 and FC3 controllers. Available with 4 AWG or 6 AWG terminals. Connector housing is genderless, so the same connector is installed on both the power and load side. Install terminals to wire with APP®...

Hardware pack includes:4X 1.5X6 Viton O-Ring1X 2X11 Viton O-Ring1X 2X26 Viton O-Ring1X 908 Viton O-Ring4X M5X20 SHCS Bolts2X M5X100 SHCS BoltsAlso included: o-ring for feed and return.Choose the correct replacement Viton o-ring set:Type A - Use with GSS342, F90000262, F10000302 fuel pumpType B -...

Aerospace grade trigger switch for secondary pumps Gold plated internal contacts and Kapton diaphragm ensure reliable long term service Preset for 4 psi actuation (ON/CLOSED above 4-5 psi) 1/8 NPT male interface is compatible with our push on boost/vacuum hose and fittings Optional sealed...

Connect aftermarket fuel rails to the OEM fuel line Adapter only, crossover line and fuel rails not included

For 2015+ Hellcat or Demon (not SRT / RT variants)Use in conjunction with a complete return style fuel system for 1200+ rwhp with triple fuel pumps (recommended to run one pump full time, then activate secondary pumps under load). Retains OE fuel level sender,...

For 2015+ Hellcat (not Demon or SRT / RT variants) Drop in pump assembly for Hellcat Charger and Challenger Use with OE fuel feed outlet, or with upgraded feed line directly off pump module No control support (modulation or regulation): see our complete Hellcat...

For 2015+ Hellcat or Demon (not SRT / RT variants)Use in conjunction with a complete return style fuel system for 1000+ rwhp with dual fuel pumps (recommended to run one pump full time, then activate secondary pump under load). Retains OE fuel level sender,...

Lowers fuel rail ~14mm for clearance under Whipple throttle body Includes four anodized rail standoffs and new stainless screws Rails sold before July 2019 may need minor clearance work around injector boss Requires short 34mm injectors

New AC Delco sensor with universal 1/8 NPT adapter Replaces restrictive OE sensor Plugs directly into OE harness Black anodized aluminum adapter with Viton o-ring included TYPICAL USES After fuel filter in Hellcat LX/LC After fuel filter in C7 Corvette After fuel filter in...

Lowers fuel rail ~14mm for clearance under plenum and throttle body Includes four anodized rail standoffs and new stainless screws Rails sold before July 2019 may need minor clearance work around injector boss Requires short 34mm injectors Only required for Kenne Bell Mammoth, NOT...

Fuel Rails NOT INCLUDEDCrossover and OE line adapter kit includes: Does not come preassembled Fittings to interface to incoming OE feed line without binding Odorless hose assemblies using low-permeable FlexLP fuel line New rail fuel pressure sensor installed in lossless -8 feed line in...