2020 Dodge Challenger SRT Hellcat Performance Parts

Connect aftermarket fuel rails to the OEM fuel line Adapter only, crossover line and fuel rails not included

Hardware pack includes:4X 1.5X6 Viton O-Ring1X 2X11 Viton O-Ring1X 2X26 Viton O-Ring1X 908 Viton O-Ring4X M5X20 SHCS Bolts2X M5X100 SHCS BoltsAlso included: o-ring for feed and return.Choose the correct replacement Viton o-ring set:Type A - Use with GSS342, F90000262, F10000302 fuel pumpType B -...

For 2015+ Hellcat or Demon (not SRT / RT variants)Use in conjunction with a complete return style fuel system for 1200+ rwhp with triple fuel pumps (recommended to run one pump full time, then activate secondary pumps under load). Retains OE fuel level sender,...

For 2015+ Hellcat (not Demon or SRT / RT variants) Drop in pump assembly for Hellcat Charger and Challenger Use with OE fuel feed outlet, or with upgraded feed line directly off pump module No control support (modulation or regulation): see our complete Hellcat...

For 2015+ Hellcat or Demon (not SRT / RT variants)Use in conjunction with a complete return style fuel system for 1000+ rwhp with dual fuel pumps (recommended to run one pump full time, then activate secondary pump under load). Retains OE fuel level sender,...

Lowers fuel rail ~14mm for clearance under Whipple throttle body Includes four anodized rail standoffs and new stainless screws Rails sold before July 2019 may need minor clearance work around injector boss Requires short 34mm injectors

Lowers fuel rail ~14mm for clearance under plenum and throttle body Includes four anodized rail standoffs and new stainless screws Rails sold before July 2019 may need minor clearance work around injector boss Requires short 34mm injectors Only required for Kenne Bell Mammoth, NOT...

Fuel Rails NOT INCLUDEDCrossover and OE line adapter kit includes: Does not come preassembled Fittings to interface to incoming OE feed line without binding Odorless hose assemblies using low-permeable FlexLP fuel line New rail fuel pressure sensor installed in lossless -8 feed line in...

New AC Delco sensor with universal 1/8 NPT adapter Replaces restrictive OE sensor Plugs directly into OE harness Black anodized aluminum adapter with Viton o-ring included TYPICAL USES After fuel filter in Hellcat LX/LC After fuel filter in C7 Corvette After fuel filter in...

Use to plug quick disconnect EFI end of Hellcat OE fuel pressure sensor Solid EFI 3/8" male plug Black anodized aluminum See this video on how to remove sensor from OE rail assembly without scarring barb.See this video on how to install fitting on...

Install AN-8 Male adapter on barb of OE Hellcat fuel pressure sensor Reuse OE sensor in larger -8 fuel lines Black anodized aluminum bodies, brass retention nut, stainless lockring, Viton o-rings See this video on how to remove sensor from OE rail assembly without...

Install AN-8 Male adapter on EFI quick disconnect end of OE Hellcat fuel pressure sensor Reuse OE sensor in larger -8 fuel lines Black anodized aluminum Fitting part # 33-002 See this video on how to remove sensor from OE rail assembly without scarring...

Fore Innovations billet fuel rails for the Hellcat and Demon Hemi. Machined from a solid block of 6061 aluminum. Integrated mounting tabs eliminate rail tab flex under the highest intake and fuel pressures. Does not come assembled Use with OE length injectors and/or Injector...

Fifteen foot long extension pigtail for relocating the fuel pressure sensor on the following applications: Hellcat Demon Trackhawk Camaro, 5th and 6th generation CTS, 2nd and 3rd generation ATS Corvette, 6th generation ZR1, 7th generation Proper termination is required on the opposite end. Fuel...

WHIPPLE BILLET 112MM ANALOG THROTTLE BODY FOR WHIPPLE 3.8L HELLCAT/HEMI SUPERCHARGER APPLICATIONS With the ever increasing demand for power, Whipple offers a high quality, high flow electronic throttle body designed for Whipple 3.8L Hellcat/Hemi supercharger systems. The 112mm throttle opening is intended to help...